LUBA 1 AWD

2023 (legacy, discontinued)

7 entries, recently updated first

Guide LUBA 2, LUBA 2X (most also applies to LUBA 1)

LUBA 2/2X charging and docking failures: a dealer's diagnostic walkthrough

An authorized Mammotion dealer's step-by-step breakdown of docking/charging failures: contact alignment, the power-supply and charging-station LED codes, ant infestations, and how to tell a bad battery from a bad power supply.

Last updated 03 Nov 2026

Known issue YUKA (sub-model not stated in most reports), LUBA Mini AWD LiDAR, and LUBA 1 / LUBA 2 (cross-model corroboration)

Error 1200 (Recharge failed): reported across multiple models, at least three distinct causes

"Recharge failed (1200)" has been independently reported across the YUKA line, LUBA Mini AWD LiDAR, and LUBA 1 / LUBA 2 units, with several confirmed different causes: a faulty charging station whose light has gone dark, a dock that passes every check and still fails, and an unlevel dock. Check each before assuming a mower-side fault.

First reported 08 Jun 2024 Last updated 03 Nov 2026

Known issue LUBA 2 (base/2024), also reported on LUBA 1

LUBA 2: charging station's green status LED goes dark, mower stops docking on its own

Four independent LUBA 2 (and one LUBA 1) owners hit the same pattern within weeks of each other: the charging station's green LED goes dark and the mower stops finding its own way home, even though it still charges fine when placed on the dock by hand.

First reported 08 Jun 2024 Last updated 03 Nov 2026

Guide LUBA 1 AWD (unconfirmed: the 2023 posts say only LUBA)

LUBA firmware version history, May to October 2023, from Mammotion's own release posts

The eight 2023 LUBA firmware releases, 1.7.2.247 to 1.10.4.223, as Mammotion announced each one on its own Reddit forum.

Last updated 25 Oct 2026

Known issue LUBA 1 AWD

LUBA 1 after firmware 1.11.1.11 and 1.11.1.16: slower turns, spinning in place, crossed boundaries

LUBA 1 owners report turns that got slower and clumsier after firmware 1.11.1.11, the mower spinning in place or going round in circles at row ends, and crossing no-go zones. Version 1.11.1.16's notes, as an owner quotes them, list a boundary fix and smoother multi-point turns; owners are split on whether it helped.

First reported 24 Aug 2026 Last updated 24 Oct 2026

Guide YUKA, LUBA 2, LUBA 1 (any RTK/NetRTK-equipped model: this is a signal-placement issue, not model-specific firmware)

RTK base station placement: why 'full satellite count' doesn't mean good signal

An owner's side-by-side test shows light tree canopy over the RTK base station caused repeated positioning loss and missed rows, even while the app reported 40+ satellites. Covers why attics are a bad RTK location, and that moving the base station destroys all saved maps.

Last updated 30 Sep 2026

Known issue LUBA 1, LUBA 2 AWD X 5000X

LUBA charging stations: stuck or corroded contact pins block charging

Four independent owners traced a repeated dock-and-retry loop, or a sudden total charging failure, to the same physical part: the charging station's spring-loaded contact pins. Two found a pin physically stuck (heat, then insects); the third found pins that looked clean, and a fix only polishing made, with the power draw at the plug as proof. A fourth freed a merely sticking pin with a little WD-40, as Mammotion's own reply advised.

First reported 27 Jun 2025 Last updated 30 Sep 2026

Nothing here matches your symptom?

If yours isn't here, it may not have been reported enough times to confirm yet. That doesn't mean it isn't real.

Do this first: common mechanical causes
Many symptoms that look like firmware turn out to be physical — a loose cutting disc, gummed-up wheel shafts, grass buildup, an unlevel charging dock. Cheaper and faster to rule out than a rollback.
Issues we're watching
Problems confirmed by two or more independent owner reports but not yet pinned to a specific firmware or app version. If yours is there, a new report with version details is what promotes it to a full guide.

What to have ready before you contact Mammotion support

Support resolves cases fastest when the report is specific. "It broke after the update," with no version number, is very hard for anyone — including Mammotion — to act on.

Exact model and variant, including any suffix — e.g. LUBA 2 AWD 5000X vs. 5000 (the "H" suffix means a taller cutting-height range, not a different generation).
Your mower's body firmware version — usually under Device Info / About Device in the app (a longer string like 1.30.29.26). Separate from the app version.
Your companion app version — from the app's own About/Settings screen.
The exact symptom, and what the mower was doing when it started.
Whether it began right after a firmware or app update, and which one.
Any in-app error code, and roughly when it appeared.
The app's event log or diagnostic report, if your model provides one.
Photos or a short video, if the issue is physical (docking, damage, turf).

Mammotion lists its support channels by region — including a 24/7 live chat — at mammotion.com/pages/contact-us. Regional support email: support-na@ (North America), support-eu@ (Europe), support-apac@ (Asia Pacific).

Found something we don't cover yet? Send us the details — that's how the next owner finds it documented.