YUKA

1000 · 2000 · 3000 · YUKA 2024 (legacy)

10 entries, recently updated first

Reference LUBA 2 AWD, LUBA 2 AWD X, LUBA mini AWD, LUBA mini AWD LiDAR, YUKA, YUKA mini & YUKA mini Vision (see scope note for what's not covered)

Mammotion fault & error code reference

Official Mammotion fault/error codes, meaning and manufacturer-recommended fix for each, cross-checked against seven current official user manuals, plus which model lines' manuals don't document fault codes at all.

Last updated 03 Nov 2026

Known issue LUBA 2, LUBA 2X, YUKA, LUBA mini Series & YUKA mini Series

LUBA 2 / LUBA 2X / YUKA / mini series: firmware 1.30.29.24 → 1.30.29.26, the same perimeter issue fixed twice, two weeks apart

Mammotion's official August 21 and September 4 firmware announcements both claim to fix the mower crossing the perimeter/no-go zones. Here's what actually changed between them, and what's been reported since the second fix.

Released: 21 Aug 2026

First reported 29 Aug 2026 Last updated 03 Nov 2026

Known issue YUKA, YUKA mini (also reported, less specifically, on LUBA)

Error 1028 ("drivetrain motor error detected"): owners link it to a stuck wheel; Mammotion calls it occasional

Not in any official manual. Owners saw it right after a wheel got physically stuck. Mammotion's reply in the forum thread called it an occasional problem and said safety is generally not affected, without naming a cause. Reported on YUKA, YUKA mini, and (per one forum regular) LUBA.

First reported 09 Jun 2025 Last updated 03 Nov 2026

Known issue YUKA (sub-model not stated in most reports), LUBA Mini AWD LiDAR, and LUBA 1 / LUBA 2 (cross-model corroboration)

Error 1200 (Recharge failed): reported across multiple models, at least three distinct causes

"Recharge failed (1200)" has been independently reported across the YUKA line, LUBA Mini AWD LiDAR, and LUBA 1 / LUBA 2 units, with several confirmed different causes: a faulty charging station whose light has gone dark, a dock that passes every check and still fails, and an unlevel dock. Check each before assuming a mower-side fault.

First reported 08 Jun 2024 Last updated 03 Nov 2026

Known issue LUBA 2, LUBA 2 AWD, LUBA 3 AWD, YUKA 2000, YUKA mini 2 800

Charging stops part-way, around 40 to 75%: LUBA 2, YUKA and YUKA mini 2

Owners report charging that stops between about 40 and 75% and waits there, on LUBA 2, YUKA 2000 and YUKA mini 2 800. Mammotion's 2.3.31.69 notes fix charging that fell short of the set level on the LUBA 3 and mini 2 line; for the LUBA 2 and YUKA line, support has pointed owners at the power adapter's batch number.

First reported 06 Sep 2026 Last updated 24 Oct 2026

Known issue YUKA mini series, YUKA, YUKA mini 2, LUBA mini AWD, LUBA 2 (base & AWD X) & LUBA 3 3000

Error 1425 (vision module fault): reported across YUKA, YUKA mini, YUKA mini 2, LUBA mini AWD, LUBA 2 (base & AWD X) & LUBA 3

"Error detected in the 3D vision module (1425)" has shipped as an official fix on four model lines and been independently owner-reported on four more, with at least five different causes. Here's what's confirmed for each, so you're not chasing the wrong fix.

First reported 15 Jul 2024 Last updated 24 Oct 2026

Known issue RTK reference station; YUKA (2024)

RTK station after firmware 1.16.1.2: a blinking blue light and "RTK Reference Station Is Not Ready"

Owners who updated the RTK reference station to 1.16.1.2 in September 2026 saw its light blink blue or go out, and the app report the station not ready. Cutting the station's power for a few minutes brought it back for most of them.

First reported 21 Sep 2026 Last updated 18 Oct 2026

Known issue YUKA (2025) & LUBA 2 AWD X

YUKA / LUBA 2 AWD X: mower stops at night claiming the vision module is dirty when it isn't

The mower repeatedly halts during night mowing with a "vision/camera dirty" warning, on two different models, despite the lens being clean and daytime mowing working fine.

First reported 21 Aug 2026 Last updated 03 Oct 2026

Guide YUKA, LUBA 2, LUBA 1 (any RTK/NetRTK-equipped model: this is a signal-placement issue, not model-specific firmware)

RTK base station placement: why 'full satellite count' doesn't mean good signal

An owner's side-by-side test shows light tree canopy over the RTK base station caused repeated positioning loss and missed rows, even while the app reported 40+ satellites. Covers why attics are a bad RTK location, and that moving the base station destroys all saved maps.

Last updated 30 Sep 2026

Known issue YUKA mini 800 (two reports, one naming the 2025 model), plus a third YUKA owner who does not name their model

YUKA mini 800 will not charge after an update: three owners, one workaround

Three independent YUKA owners lost charging around an update cycle: one on firmware 1.30.29.24 with the battery stuck at 0%, one whose battery drops to 0% mid-task and never recharges, one whose mower 'refuses to charge properly' alongside a cluster of other things that broke. One of them got charging back by unplugging the battery.

First reported 11 Sep 2026 Last updated 21 Sep 2026

Nothing here matches your symptom?

If yours isn't here, it may not have been reported enough times to confirm yet. That doesn't mean it isn't real.

Do this first: common mechanical causes
Many symptoms that look like firmware turn out to be physical — a loose cutting disc, gummed-up wheel shafts, grass buildup, an unlevel charging dock. Cheaper and faster to rule out than a rollback.
Issues we're watching
Problems confirmed by two or more independent owner reports but not yet pinned to a specific firmware or app version. If yours is there, a new report with version details is what promotes it to a full guide.

What to have ready before you contact Mammotion support

Support resolves cases fastest when the report is specific. "It broke after the update," with no version number, is very hard for anyone — including Mammotion — to act on.

Exact model and variant, including any suffix — e.g. LUBA 2 AWD 5000X vs. 5000 (the "H" suffix means a taller cutting-height range, not a different generation).
Your mower's body firmware version — usually under Device Info / About Device in the app (a longer string like 1.30.29.26). Separate from the app version.
Your companion app version — from the app's own About/Settings screen.
The exact symptom, and what the mower was doing when it started.
Whether it began right after a firmware or app update, and which one.
Any in-app error code, and roughly when it appeared.
The app's event log or diagnostic report, if your model provides one.
Photos or a short video, if the issue is physical (docking, damage, turf).

Mammotion lists its support channels by region — including a 24/7 live chat — at mammotion.com/pages/contact-us. Regional support email: support-na@ (North America), support-eu@ (Europe), support-apac@ (Asia Pacific).

Found something we don't cover yet? Send us the details — that's how the next owner finds it documented.